How do I setup my Netgear WiFi Extender ex6120?

Netgear EX6120 extender setup manually?

  • Plug In: Connect your Netgear EX6120 extender to a power outlet.
  • Power On: Wait for the Power LED on the extender to light up.
  • Connect Device: Use your computer or mobile device to connect to the “NETGEAR_EXT” WiFi network.
  • Open Browser: Launch a web browser and go to “”
  • Follow Setup: Complete the setup by following the on-screen instructions to select and connect to your existing WiFi network.
  • Relocate Extender: Move the extender to a position that optimizes WiFi coverage. Setup is complete, and you now have extended WiFi in your desired areas.

Note:- If you need any assistance regarding your Netgear EX6120 wifi extender so contact our technician or visit the official website that is setup.

How do I set up my Netgear WiFi range extender using WPS?

  • Make sure your Netgear WiFi range extender is turned on by plugging it in.
  • Find and push the WPS button on your extension. The WPS LED ought to begin to flicker.
  • Press the WPS button on your WiFi router to enable WPS in two minutes. A secure connection will be made between the router and the extension.
  • Await Connection: Give the router and extender time to connect. Upon successful configuration, both devices’ WPS LEDs ought to glow solid.
  • If necessary, relocate the extender to a spot in your house that will maximize WiFi coverage.
  • To connect to the extended network, use your WiFi-capable devices with the same SSID as your primary router, plus “_EXT”.You 

Why can’t I log into my NETGEAR EX6120 extender?

  • Verify that your laptop or mobile device is linked to the WiFi network that your Netgear EX6120 extender—typically dubbed “NETGEAR_EXT”—is broadcasting.
  • Open a web browser on the device that’s connected.
  • Put down your address here: Type “” into the browser’s address box and hit Enter. An alternative is to use the IP address of the extender, which is often “”
  • Your Netgear extender login information will need to be entered. Use the credentials you previously set up, or use the default username and password, which are often “admin” for both.
  • The Netgear Genie setup dashboard will be accessible to you once you have entered the right credentials. This is where you control and personalize your extender settings.
  • Always log out of the dashboard when finished for security reasons.

How do I update my Netgear extender firmware?

  • Verify that the Netgear EX6120 extender’s WiFi network is accessible from your computer or mobile device.
  • Open a web browser on the device that’s connected.
  • The Interface of Access Extender: Enter “” or the IP address of the extender (usually “”) in the address box and hit Enter.
  • Enter the login information for your Netgear extender. Use the default login credentials (“admin” for both) if you haven’t set any custom ones.
  • Go to the “Settings” or “Firmware Update” section after logging in. Search for a setting similar to “Firmware Update” or “Check for Updates.”
  • If a new firmware version is available, download and install it by following the instructions on the screen. Make sure not to pause the procedure in order to avoid any problems. 

How do I reset my ex6120?

  • Look for the Netgear EX6120 extender’s reset button. Usually, it’s a tiny, inset button.
  • Press and hold the reset button with a paperclip or other comparable instrument. Hold it for five to ten seconds.
  • Let go of the reset button after holding it for a while. During the restart of the extender, the Power LED can blink.
  • Give the extender time to finish rebooting. It could require one or two minutes.
  • The extender will revert to its original factory default settings after restarting. It might require you to reset it with the default passwords and adjust your WiFi settings as necessary.

More from this stream


Notice: ob_end_flush(): Failed to send buffer of zlib output compression (1) in /home/acc714techradar/public_html/wp-includes/functions.php on line 5373

Notice: ob_end_flush(): Failed to send buffer of zlib output compression (1) in /home/acc714techradar/public_html/wp-includes/functions.php on line 5373